Plastering over Artex®
If you decide that artex remover is not for you then Artex® can be plastered over. Firstly make absolutely sure that there are no flaking or loose sections of the artex®, or indeed ceiling or wall. Then remove all obviously “high spots” of artex®, where the stipples hang down.
Does plastering over artex work?
9 Answers from MyBuilder Plasterers
Any artex must have a backing (bonding) coat applied first as as skim coat is only 3 mm thick. Once the bonding coat is dry you apply PVA to reduce suction when skimming the top coat. This will give you the desired flat finish. Hope this helps.
Does Artex devalue house?
Now, Artex ceilings can actually devalue a house. It’s very difficult to match up new repairs onto old Artex patterns. Undamaged and painted Artex is usually harmless. However, many people don’t like asbestos–based building materials in their home and will take any opportunity to remove it.
How do you get rid of Artex swirls?
The most popular way to remove Artex is to use a steamer to loosen it and then ease it off with a scraper. This process is slow but effective, if you hold the steamer in the same place for too long, however, the Artex will liquefy and run everywhere making a mess.
Is Artex worth removing?
Artex is often considered outdated and removing it can be difficult and dangerous if you’ve never done it before and are not using a safe and non-toxic remover like X-Tex. You can plaster over the textured wall or ceiling covering however this is much like sticking a plaster over something that may rear its head again.
How do you flatten an Artex ceiling?
Using the spatula, load the smoother with Artex Easifix Smooth-It. Apply an even coat with firm, sweeping strokes. When the whole surface is covered, allow to dry until firm to the touch. Repeat the process as many times as required to reach the desired smoothness.
Is it safe to skim over asbestos Artex?
Can I cover up or skim over textured coatings that contain asbestos? If the textured coating/Artex is in good condition then it is safe to apply a sealant, cover the coating with new plasterboard or skim over it with a new layer of plaster.
Can you skim over textured ceiling?
With painted texture, some pros scrape as best they can and then ‘skim coat’ the entire ceiling with a thin layer of joint compound. Scraping dry texture is a dusty mess, and skim coating requires some practice.
Do I need to PVA over Artex before plastering?
The PVA can be applied the day before as the artex provides a rough surface which will act as a good key. If it is really smooth though you need to either apply the plaster when PVA is tacky or if wanting to PVA day before a handful of sand mixed in with PVA will provide a rough surface for plaster to stick to.
Can you panel over Artex walls?
Wall Panelling can be applied directly over Artex and is easy to install with a simplistic tongue and groove interlocking system.
When did Artex go out of fashion?
Artex ceilings
Sometimes referred to as ‘popcorn’ or ‘cottage cheese’ ceilings, they fell out of favour years ago, not only because the look was no longer considered fashionable, but also because until the mid-80s Artex was made with white asbestos to make it stronger.
How do I remove swirl textured ceiling?
To remove the swirl, use a 2-inch wide carbide-tipped scraper to knock down any small ridges that stick up above the main surface. Skimcoat the ceiling and then paint. With popcorn ceilings, we’ve used paint scrapers to remove the popcorn manually prior to skimcoating with plaster.
When did Artex stop having asbestos?
When was asbestos banned from Artex in the UK? Although asbestos-containing Artex ceased production in the UK in 1984, it took until 1992 for its use to be formally prohibited by EU and UK legislation. However some usage continued even though it was prohibited. This was mainly due to using up of held stock.
