This evolved plywood may claim an overall advantage over OSB, since plywood is a stiffer, longer-lasting subfloor option. It will also hold up better under flooring accidents like leaks or flooding, and has greater nail withdrawal strength to hold the nail in under stress.
How thick should OSB subfloor be?
The minimum thickness of plywood for subflooring is about 5/8 inch. Since it does not hold fasteners as well as plywood, OSB must be a little thicker, or at least 23/32 inch.
What is the best material for a subfloor?
Plywood has been a standard subfloor material since the 1950s and remains the preferred subflooring for many builders. Standard plywood can be used for subfloors, but a better material is 3/4-inch tongue-and-groove plywood subflooring.
Can OSB subfloor get wet?
Your framing lumber and the oriented strand board (OSB) are going to be fine. The glues used to make OSB are water-resistant because the manufacturers know that virtually no one can build a home that won’t get wet before the roof and siding is applied.
Is it better to nail or screw subfloor?
Using code-approved screws rather than nails is the best option for avoiding movement. If using nails for subfloor installation, stick with ring-shank nails; smooth nails may withdraw easier, leading to squeaks.
What is stronger OSB or plywood?
Osb is stronger than plywood in shear. Shear values, through its thickness, are about 2 times greater than plywood. This is one of the reasons osb is used for webs of wooden I-joists. However, nail-holding ability controls performance in shear wall applications.
Do you need tongue-and-groove for subfloor?
For subflooring, you use tongue and groove plywood. The tongue and groove are only along the 8 foot edges. On the four foot edges, your seams will fall on joist tops, so no need for tongue and groove.
Which side of OSB subfloor goes up?
OSB roof panels should always be installed with the grade stamp facing into the attic and the screened surface (with the nail guide lines) facing up.
What is the best wood for subfloor?
Plywood is considered the most popular material used for subflooring, it has been used since the 1950s and remains one of the top choices for contractors. Standard plywood works perfectly fine as a subflooring material, but the best option is ¾” tongue-and-groove plywood subflooring.
What are 3 common subfloor materials?
Common Subfloor Materials. There are four primary materials used as subfloor: plywood, oriented strand board (OSB), concrete, and high-performance panels. There are other subfloors materials out there, but they are used in more niche situations. The construction industry is constantly evolving.
Can you use 7/16 OSB subfloor?
Oriented strand board, or OSB, is a wood structural panel that can also be used for flooring. It is made from shredded strands of wood pressed together with wax and a special adhesive, then hot pressed into a panel with up to 50 layers of strands. OSB can be used for subfloors, although it is not as common as CDX.
Can you use OSB for bathroom subfloor?
Enhanced OSB
These are typically the types of subfloors that are used in bathrooms. Although OSB is a more cost-effective solution, it can swell around the edges when exposed to water. This swelling can cause problems with your flooring, particularly if you have tile installed.
Is OSB safe indoors?
OSB can be used on interior walls since it is strong, durable, and provides structural support. The wood strands add a chic decorative finish if you are wanting the walls to stand out. Leave them unpainted for a raw decorative element or seal and paint them for stylish textured walls.
What can OSB be used for?
Applications. OSB is extensively used for wall sheathing, floor underlayment, roof cover and I-joist in both commercial and residential building. OSB also is used in furniture, reels, trailer liners and recreational vehicle floors. Figure 3 shows siding and I-joist application of OSB in building construction.
