An Eave is defined as the edge of the roof that overhangs the face of a wall. This is the portion of the roof that protrudes beyond the side of a house or building. In contrast, a Gable (or Rake) is the overhang of a building that occurs on the side that is topped by a gable roof.
Do gutters go on eaves or rakes?
Rain gutters should be positioned to extend beyond the eaves of a roof to collect rain and hail runoff. Gutters are placed on all sides of a home along the roof edge.
What is a roof rake?
Instead, the rake refers to the sloped sides of a gable style roof. This type of roof is one of the most common in colder or temperate climates, and consists of two roof sections sloping in opposite directions from the peak to allow for the best flow of precipitation off the roof.
Is fascia on eaves or rakes?
Fascia. A decorative board extending down from the roof edge either at the eave or at the rake.
What is the difference between fascia and eaves?
is that fascia is a wide band of material covering the ends of roof rafters, sometimes supporting a gutter in steep-slope roofing, but typically it is a border or trim in low-slope roofing while eaves is the underside of a roof that extends beyond the external walls of a building.
Does rake need drip edge?
A drip edge should be installed on the eaves and rakes of the roof, flush with the decking and fascia. On eaves, the drip edge is installed directly to the deck with underlayment installed over it for proper water shedding. On rakes, the underlayment is installed over the drip edge.
What is the difference between an eave a rake and a ridge?
Rake – The outer edge of the roof from the eave to the ridge. Ridge – An intersection of two roof planes forming a horizontal peak.
What is the overhang on a roof called?
Soffit: The underside of the eaves, or roof overhang, which can be enclosed or exposed.
What is roof eave?
Eaves: The eaves are the lower edges of the roof that overhang the home’s exterior walls.
What are rake rafters supported by?
what is a gable/rake lookout? framing member fastened to a common rafter and cantilevered outward over the gable rafter to support the rake rafter. where are the gable studs? vertical studs extending from the cap plate on the wall to the underside of the gable rafter.
What is the difference between gable and rake?
Rake—The slanting edge of a gable roof at the end wall of the house. Ridge—The horizontal line at the top edge of two sloping roof planes. Sheathing—The decking material (usually sheets of plywood), which is nailed to the rafters, and to which shingles or other outside roofing materials are secured.
What is a rake soffit?
Purpose of a Rake Board
The rake board covers the top edge of the siding where it meets the roof, or soffit if there is an overhang on the gable end, and prevents rain from running behind it. Rake boards are installed on the gable ends of brick houses to cover the exposed top edge of the brick.
What is a rake overhang?
The American Wood Council’s 2012 Wood Frame Construction Manual defines rake overhang as “The horizontal projection of the roof measured from the outside face of the gable endwall to the outside edge of the roof.” Section 2.1. 3.4.
What is the top of the roof called?
Roof Ridge: The roof ridge, or ridge of a roof is the horizontal line running the length of the roof where the two roof planes meet. This intersection creates the highest point on a roof, sometimes referred to as the peak. Hip and ridge shingles are specifically designed for this part of a roof.
Are roof rakes bad for roofs?
Never, never use a roof rake or try to shovel snow off a slanted roof. It will do no good, will not cure ice dams, is extremely hazardous, and can harm asphalt shingles, and in your case, slate shingles. And it will take away snow that is a natural insulator as long as it stays on your house.
Can a roof rake damage shingles?
Use a snow rake for pitched roofs (available at most hardware stores) to remove snow from your roof. Start from the edge and work your way into the roof. Try to shave the snow down to a 2 or 3 inches on the roof instead of scraping the roof clean, which will risk damage to your shingles or other roof covering.
