What are the socket wrench sizes?

There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In-between sizes are available too, starting with 1/4 inch (0.6 centimeters) and increasing every sixteenth of an inch (0.16 centimeters).

Furthermore, how do I know my socket size?

Place the end of a measuring tape on one of the flat sides of the nut's outer perimeter. Stretch the tape measure across the nut's diameter to the flat-side directly across from the one your pulling from. If the nut is metric, count the number of lines on the tape measure to find the measurement.

Subsequently, question is, what are the SAE wrench sizes? Society of Automotive Engineers (SAE) measurement 3/8 in, 7/16 in, 1/2 in, 9/16 in, 5/8 in, 11/16 in, 3/4 in, 13/16 in, 7/8 in, 15/16 in, 1 in, 1-1/16 in, 1-1/8 in, 1-3/16 in, 1-1/4 in.

Also to know, what are the different wrench sizes?

Wrenches: Standard Combination Wrenches (1/4, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1) Metric Combination Wrenches (6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19) Standard Flare Nut Wrenches (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 7/8) Note: Each wrench may combine two sizes.

How do I know what size wrench to use?

Multiply the first number which is the bolt size in inches or millimeters, by 1.5 using a pocket calculator, if necessary. For example, for the numbers in Step 1, 1/2 x 1.5 = . 75 or 3/4, which is the wrench size needed for this standard-sized bolt.

How do you remove a ratchet socket?

Guide to Removing a Socket Stuck in a Ratchet Place the turning tool upside down so that the socket head is pointing vertically upwards. Spray the penetrating oil into the socket and let it run down through the drive socket. Leave the socket for a few minutes for the penetrating oil to take effect.

What are the sizes of standard sockets?

Six Point Standard Sockets (5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16) Six Point Metric Sockets (8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21) Six Point Metric Deep Sockets (8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19) Hex Bit Standard Sockets (5/32, 3/16, 7/32, 1/4, 5/16, 3/8)

What size socket set should I buy?

While 12-point sockets are fine for most light work, choose six-point sockets for larger hardware or applications that demand serious torque. Six-point sockets are less likely to slip in this situation.

What size nut fits a 15mm socket?

The standard wrenches needed are: 11,13,15,17,19,22,24,27,30,32,36mm. I believe that the bold that goes with the 15mm wrench is normally an M8. M8s usually use 12 or 13mm heads.

How do you measure bolt head for socket?

How to Measure the Socket Wrench Size for a Bolt

Insert the shank of the bolt into the holes in a bolt-sizing gauge.
Locate the printed bolt size to the side of the correct hole on the gauge (for example, 1/2, 3/4 or in mm for metric bolts).
Locate the socket head in the socket set that has this size printed on its side.

What is a thin wrench called?

They are called tappet wrenches, for automobile/general use.

What is bigger than a 7 8 wrench?

To learn more about the information we collect and use for advertising purposes, please see our Privacy Policy.

Wrench Size Chart for Bolts.

Bolt Diameter	Wrench Size (Standard)	Wrench Size (Metric)
5/16"	1/2"	13mm
3/8"	9/16"	15mm
7/16"	5/8"	16mm
1/2"	3/4"	19mm

What are the most common metric wrench sizes?

Re: Most common metric bolt sizes Used to be (back in the 70's and 80's) that European manufacturers used the 13mm and 10mm fasteners the most; followed by the 14, 17, and 19mm. The Asian manufacturers used the 12mm and 10mm as the most common, followed by the 15, 17 and 19mm.

What's the next size smaller than a 9/16 wrench?

Wrench Size Chart for Bolts

Bolt Diameter	Wrench Size (Standard)	Wrench Size (Metric)
7/16"	5/8"	16mm
1/2"	3/4"	19mm
9/16"	13/16"	21mm
5/8"	15/16"	24mm

Is a 3/8 socket the same as a 10mm?

It's the same size. 3/8 is in inch and and its 10mm.

What is the largest wrench size?

30-inch Adjustable Wrench VS Cheater Wrench Channellock came out with the largest adjustable wrench on the market.

What are the standard wrench sizes?

Standard wrench comes in size such as 1/4, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16 and 1.

What is equivalent to a 16mm wrench?

Standard / Metric Wrench Conversion Chart

Bolt Diameter	Standard	Metric
5/16"	1/2"	13mm
3/8"	9/16"	14mm
7/16"	5/8"	16mm
1/2"	3/4"	19mm

What is the most common ratchet size?

Common ratchet sizes include 1/4-inch drive, 1/2-inch drive and 3/8-inch drive. Having different socket wrench sizes will allow you to operate different socket sizes based on your particular needs.